Product code:  0110 Producer: Protex (Україна)

Bentonite cord 15x25 mm for waterproofing and sealing working seams, 5 m.p.

195 Product code:0110 Producer: Protex (Україна)

Bentonite cord 15x25 mm for waterproofing and sealing working seams, 5 m.p.

To ensure waterproofing of working seams in building structures

195 uah / pog.m

+38 067 414 61 38
0 800-400-212

Waterproofing bentonite cord "Hydrostop RED" 15x25 mm is a material designed to ensure the waterproofness of working seams in building structures and in places of communication. When in contact with water, the bentonite cord significantly increases its volume. The resulting gel in a confined space creates a stress that reduces water permeability, even in the presence of cracks and porous places in the concrete. To achieve complete sealing and isolation from moisture, the bentonite cord "Hydrostop RED" 15x25mm in the form of a tape is mounted in the seams of foundations and walls with steel nails every 30-40 cm to avoid displacement and to achieve a better connection with concrete. When mounting, it is necessary to avoid breaking the continuity of the tape position. Excellent technological performance and an easy installation method make it possible to use the product as an insulating material for joints in underground construction, hydraulic structures and civil engineering. Bentonite cord "Hydrostop RED" has a cross-section of 15x25 mm, is made of bentonite clay and is a rectangular cross-section profile that swells when in contact with water. The cord increases in volume by 4 times, i.e. by 400%, while being in the concreted joints, it covers absolutely any cracks and holes. Bentonite cord securely and firmly adheres to the concrete surface, filling seams, junctions and the smallest voids in the concrete body, forming a reliable protective layer.

Main Features:

  • excellent technological performance
  • easy installation method
  • the ability to use the product as an insulating material
  • for seams in underground construction
  • use on hydraulic structures
  • use in civil engineering

Sold in boxes of 5 m.p.

Scope of application:

  • Concreting break seams: cold, working seam
  • Inputs of engineering communications
  • Holes in concrete after removing the formwork

Advantages:

  • low cost
  • easy installation (does not require highly qualified installers and special tools)
  • wide operating temperature range without loss of properties -30° to 50°C
  • installation on a wet base is possible
  • plasticity
  • withstands hydrostatic effects up to 7 atmospheres.

Method of installation and installation:

Installation of bentonite cord depends on its type and is carried out using a special mesh, sealant or glue. To achieve complete sealing and isolation from moisture, the bentonite "Hydrostop RED" 15x25mm harness in the form of a tape is mounted in cold joints of foundations and walls with steel nails every 30-40 cm to avoid displacement and to ensure better connection with concrete. When mounting, it is necessary to avoid breaking the continuity of the tape position.

 

Density, g/cm3: 1.5

The color is red

Packaging: Rolls of 5 m

Boxes: 40 m each (8 rolls)

Flexibility on a beam with a radius of R=25 mm:

at a temperature of minus 30 °C: no cracks

at a temperature of plus 50 °C: no cracks

Volumetric expansion after exposure to water, %
- after 24 hours: 25
- after 48 hours: 80
- after 7 days: 210

Tensile strength, N, not less than: 18

Relative elongation at break, % not less than: 25

Bentonite cord "Hydrostop RED" 15x25 mm is an important material for ensuring tightness and protection of construction structures from moisture. Here are the basic steps for its stacking and installation:

Surface preparation : The surface on which the cord will be laid must be clean, dry and free from dust, dirt or other contaminants.
Measuring and Cutting: Measure the length of the seam to be filled. Cut a suitable length of bentonite cord with a spare.
Laying the cord: Place the bentonite cord inside the joint or suitable space, making sure it fits snugly against the walls of the joint or hole.
Fixation: To ensure a better fixation and bond with the concrete, use steel nails or other suitable fasteners. Install them every 30-40 cm along the seam or as needed.
Continuity check : Do not allow the continuity of the position of the cord in the seam. Make sure the cord is laid without gaps or overlaps to ensure continuous protection against moisture.
Additional fixation (if necessary) : If necessary, apply a special mesh, sealant or glue for additional fixation and sealing of the seam.
Checking the quality of the installation: After the installation is complete, check the quality of the installation, making sure that the cord fits tightly to the surface and provides reliable insulation.

Correct installation of "Hydrotop RED" bentonite cord is important to ensure effective protection against moisture and maintain the integrity of the building structure. When performing work, the manufacturer's recommendations should be followed and appropriate personal protective equipment should be used.

What is the method of laying and installing bentonite cord?

Installation of bentonite cord depends on its type and is carried out using a special mesh, sealant or glue. To achieve complete sealing and insulation from moisture, the bentonite harness "Hydrostop RED" in the form of a tape is mounted in the cold seams of the foundations and walls with the help of steel nails every 30-40 cm to avoid displacement and to make a better connection with the concrete. During mounting, it is necessary not to allow a violation of the continuity of the position of the tape.

How to choose the right bentonite cord?

For sealing technological seams, the size of the bentonite cord is selected depending on the thickness of the concrete wall or slab and the technological characteristics of the structure.

  • for sealing the holes - bentonite cord with a round section with a diameter of 22 mm.
  • for the introduction of communications - a rectangular section of 5x20 mm.
  • for sealing cold seams - rectangular section 10x20; 15x25; 20x30 mm.

Delivery methods:

  • Delivery by courier in Kyiv (1-3 working days, cost according to the carrier's tariffs);
  • Address delivery by Nova Poshta Courier (1-3 working days, cost according to the carrier's tariffs);
    The cost of delivery is based on the carrier's tariffs
  • Nova Poshta in Ukraine (1-3 working days, cost according to the carrier's tariffs);
    The cost of delivery is based on the carrier's tariffs
  • Pickup from the Protex warehouse — Free;
    (The address of the warehouse: Kyiv, 9 Pshenychna Street. The goods can be received from 9:00 a.m. to 5:00 p.m., from Monday to Friday.)

Payment methods:

  • Postpaid "Nova Poshta"
    The buyer-recipient of the parcel pays a commission of 2% + UAH 20 from the amount of the order.
  • Payment by bank card (Privatbank 4246 0010 3027 1724)
    (Recipient: Fedchenko Svitlana Serhiivna)
  • Payment by details (PrivatBank)
    IBAN account: (UA103052990000026000005026855)
    Recipient: FOP Fedchenko Svitlana Serhiyivna,
    EDRPOU: 2745422924

Супутні товари