Product code:  0160 Producer: Protex (Україна)

Clamping screw for formwork 15/17, 3 m.p.

605 Product code:0160 Producer: Protex (Україна)

Clamping screw for formwork 15/17, 3 m.p.

Screed screw for screed boards of formwork, plywood, OSB

605 uah / шт

+38 067 414 61 38
0 800-400-212

Formwork clamping screw is used for screeding formwork boards, plywood, OSB. The tightening screw is made of high-strength, high-quality steel, which allows it to withstand high loads. The main feature of the tightening screw is its low weight and specially rolled thread, which allows you to unscrew the nuts for the formwork without extra effort, even when the area of the wine is contaminated. for the screed of light vertical formwork and self-made formwork. It is used together with a super plate or a wing nut. Anchor screws and tie nuts take the pressure of the concrete mixture, so the choice of components for formwork is of great importance for safe work. without any extra effort, even when the part of the screw is contaminated with concrete.

The Formwork Clamping Screw is used with flange nuts for light and self-made formwork or support nuts for wall formwork systems and medium and heavy series columns. Used together with nuts, protective plastic tube and cones.
They are supplied at the factory in lengths of 3 meters and are cut on the construction site according to the formwork fastening specification.
The main feature of the tightening screw is its low weight and specially rolled thread, which allows you to unscrew the nuts for the formwork without extra effort, even if the part of the screw is contaminated with concrete.
The shuttering screw for formwork is used for the screed of light vertical formwork and self-made formwork.
Used in conjunction with a super plate or ram nut.

Outer section: 17 mm
Internal section: 15 mm
Galvanized screw.
The length of one tightening screw is 3 m.

Outer section: 17 mm
Internal section: 15 mm
The length of one tightening screw is 3 m.

Screw installation instructions:

  • Choosing the installation location: Determine the point where you want to install the screw. Make sure the location you choose is free of hidden wires, pipes, or other obstructions.
  • Surface preparation: Clean the surface to which the tightening screw is attached from dust, dirt and other contaminants.
  • Determining the depth: Determine the depth to which you need to drill the hole to install the screw. This usually depends on the size and type of screw and the installation conditions.
  • Drilling a hole: Use a drill of the appropriate size to drill a hole in the surface. Make sure the hole size matches the screw size.
  • Installing the screw: Insert the screw into the drilled hole and start to screw it in by hand. If necessary, use a screwdriver or other tool to tighten the screw. Make sure the screw is firmly pressed against the surface.
  • Checking the security of the fastening: Check how firmly the screw is fixed by pulling or pressing on it. Make sure it does not move and is firmly seated in the hole.
  • Completion of the installation: If necessary, fasten the elements that are attached to the tightening screw. Then make sure the whole assembly looks neat and secure.
  • This is a general guide, and it is also important to follow the manufacturer's instructions for the specific screw, as the instructions may vary slightly depending on the type and model of the screw.

How to install a screw?

  • the installation of shields is carried out in accordance with the requirements of the project
  • pre-drill the holes before installing the shields
  • a clamping screw for the formwork is inserted into the pre-drilled hole
  • washers and nuts are put on both sides of the screeds, and they are tightened
  • dismantling is carried out after the concrete has completely hardened
  • parts are disassembled in reverse order and can be reused

Delivery methods:

  • Delivery by courier in Kyiv (1-3 working days, cost according to the carrier's tariffs);
  • Address delivery by Nova Poshta Courier (1-3 working days, cost according to the carrier's tariffs);
    The cost of delivery is based on the carrier's tariffs
  • Nova Poshta in Ukraine (1-3 working days, cost according to the carrier's tariffs);
    The cost of delivery is based on the carrier's tariffs
  • Pickup from the Protex warehouse — Free;
    (The address of the warehouse: Kyiv, 9 Pshenychna Street. The goods can be received from 9:00 a.m. to 5:00 p.m., from Monday to Friday.)

Payment methods:

  • Postpaid "Nova Poshta"
    The buyer-recipient of the parcel pays a commission of 2% + UAH 20 from the amount of the order.
  • Payment by bank card (Privatbank 4246 0010 3027 1724)
    (Recipient: Fedchenko Svitlana Serhiivna)
  • Payment by details (PrivatBank)
    IBAN account: (UA103052990000026000005026855)
    Recipient: FOP Fedchenko Svitlana Serhiyivna,
    EDRPOU: 2745422924

Супутні товари