Hydroshponka ND 200 PVC external for waterproofing deformation joints, blue, 20 m.p.
Hydroshponka ND 200 PVC external for waterproofing deformation joints, blue, 20 m.p.
Hydro-shponka ND 200 PVC outer blue PROTEX for waterproofing deformation joints, width 200 mm, bays 20 m. p.
The ND 200 hydraulic gasket is used for sealing and waterproofing movable joints in monolithic construction of buildings, including foundations, underground parking lots, tunnels, canals, etc. It is mounted directly on the formwork sheet. It is used in hydraulic structures - reservoirs, canals, dams, swimming pools, etc., as well as for waterproofing joints of foundations, foundations, tunnels, multi-level parking lots and other underground structures. They are made of thermoplastic elastomer TRE (EPDM) or plasticized PVC-p polyvinyl chloride.
- allows you to securely embed in a concrete structure
- the presence of ribs on the locking plane prevents the penetration of moisture into the structure
- the presence of a deformable area allows you to perceive deformations of reinforced concrete structures without breaking the tightness
- it is used for sealing between two concrete structures
- in particularly important constructions, it is supplemented with an internal hydraulic gasket
- it can be used in structures with special requirements to ensure tightness
- withstands high water pressure inside and outside
- suitable for all kinds of designs
- the hydraulic shponka is supplied in rolls of 20 m.p.
Material | Plasticized polyvinyl chloride (PVC-n) |
Color | Blue |
Packaging | Rolls of 20 m. p. |
Roll length deviation, m, no more | ± 0.5 |
Size deviations | According to KD |
Shore hardness, A | 70 ± 5 |
Density, g / cm3 | ≈ 1.4 |
Tensile strength, MPa | ≥10 (DIN 53455) |
Elongation at break, % | ≥ 275 |
Heat resistance, ° C | from -35 ° C to 70 ° C |
Chemical resistance | - from constant exposure to water and sewage; - from short-term exposure to inorganic alkalis and low-concentration, mineral acids |
UV resistance | Not stable |
Term of operation | not less than 25 years |
Material: plasticized polyvinyl chloride (PVC-p)
Color: Blue
Packaging: rolls of 20 m.
Roll length deviation, m: no more than ± 0.5
Dimensional deviations: according to KD
Shore hardness, A: 70 ± 5
Density, g / cm3: ≈ 1.4
Tensile strength, MPa: ≥10 (DIN 53455)
Elongation at break,%: ≥ 275
Temperature resistance, ° C: from -35 ° C to 70 ° C
Chemical resistance:
- from constant exposure to water and sewage;
- from short-term exposure to inorganic alkalis and acids of low concentration, mineral oils.
UV resistance: not stable
Service life: 25 years
Installation procedure and rules:
- The hydraulic key is installed in the design position, so that the middle of the hydraulic key is in the center of the expected deformation seam.
- Fastening is carried out directly to the formwork.
- Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor.
- The fastening step is 200-300 mm, symmetrically on both sides.
- Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire.
- The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Ten.
- The temperature of adhesion is about 200 ° C (chosen experimentally).
- To connect the keys by the "cold" method, glue is used, for example, a one-component pasty glue based on the silane-modified InnoElast polymer.
Hydro-shponka ND 200 PVC external blue PROTEX is an ideal solution for sealing and waterproofing movable joints during the construction of buildings, including foundations, parking lots and tunnels.
This is a reliable and maximally hermetic solution that provides impermeability to moisture, preventing its penetration into the structure. A special feature of this hydraulic key is the ribs on the locking plane, which prevent moisture from entering the structure.
Thanks to the deformable area, this hydraulic key is able to perceive the deformations of reinforced concrete structures without breaking the tightness. The hydraulic key can also be used to seal between two concrete structures and be supplemented with an internal hydraulic key in particularly important cases. It can be used even in constructions with special requirements to ensure reliable tightness.
Withstanding high pressure both outside and inside the structure, Hydroshponka Hydroshponka ND 200 PVC external blue PROTEX is suitable for all types of structures.
Supplied in rolls 20 meters long.
Use in your construction the maximum protection against moisture with hydroshponkoy ND 200 PVC PROTEX!
How to install a hydraulic key?
- The hydraulic dowel is installed in the design position so that the middle of the hydraulic dowel is in the center of the intended seam.
- Fastening is carried out directly to the formwork.
- Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor.
- The fastening step is 200-300 mm, symmetrically on both sides.
- Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire.
- The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Ten.
- The temperature of adhesion is about 200 ° C (chosen experimentally).
- To connect the keys by the "cold" method, glue is used, for example, a one-component pasty glue based on
- silane-modified Innoellast polymer.
Hydroshponka ND 200 PVC PROTEX is a reliable solution for waterproofing and sealing movable joints during the construction of buildings, foundations, tunnels and other structures.
This external, blue hydro-key is perfect for monolithic construction, where it is mounted directly on the formwork sheet.
With its help, it prevents the penetration of moisture into concrete structures due to the presence of ribs on the closing plane.
Due to the deformable area, the hydraulic key is able to perceive the deformations of reinforced concrete structures without breaking the tightness.
It is also ideal for sealing between two concrete structures.
Moreover, in particularly important constructions, the ND 200 PVC hydraulic plug can be supplemented with an internal hydraulic plug to ensure additional tightness.
It also perfectly copes with the special requirements that can be set for structures for the purpose of tightness.
ND 200 PVC hydro-shponka withstands high water pressure both inside and outside the structure.
It is suitable for all types of structures - from foundations to channels and tanks.
Hydro-shponka can be purchased in rolls, each of which contains 20 meters of film.
By choosing PROTEX hydro-shponka Hydro-shponka ND 200 PVC, you get a reliable and durable solution for waterproofing and sealing deformation joints.
Delivery methods:
- Delivery by courier in Kyiv (1-3 working days, cost according to the carrier's tariffs);
- Address delivery by Nova Poshta Courier (1-3 working days, cost according to the carrier's tariffs);
The cost of delivery is based on the carrier's tariffs - Nova Poshta in Ukraine (1-3 working days, cost according to the carrier's tariffs);
The cost of delivery is based on the carrier's tariffs - Pickup from the Protex warehouse — Free;
(The address of the warehouse: Kyiv, 9 Pshenychna Street. The goods can be received from 9:00 a.m. to 5:00 p.m., from Monday to Friday.)
Payment methods:
- Postpaid "Nova Poshta"
The buyer-recipient of the parcel pays a commission of 2% + UAH 20 from the amount of the order. - Payment by bank card (Privatbank 4246 0010 3027 1724)
(Recipient: Fedchenko Svitlana Serhiivna) - Payment by details (PrivatBank)
IBAN account: (UA103052990000026000005026855)
Recipient: FOP Fedchenko Svitlana Serhiyivna,
EDRPOU: 2745422924