Repair hydraulic key for expansion joints ND - r 200, PVC, bay 20 m, blue
Repair hydraulic key for expansion joints ND - r 200, PVC, bay 20 m, blue
Repair hydraulic key for deformation seams
The ND-R 200 hydraulic gasket is used for waterproofing expansion joints when mating with existing concrete and metal structures. It is used in the monolithic construction of buildings, including foundations, underground parking lots, tunnels, canals, etc. The repair hydraulic shingle is fixed to the existing structure, the free part of the hydraulic shingle is loosened to the reinforcement frame of the poured structure, immediately before pouring concrete. They are made of thermoplastic elastomer TRE or plasticized PVC-p polyvinyl chloride.
- for sealing the expansion joints between the finished w/b or metal structure and the poured structure
- for reliable fixation of the hydraulic strap, a metal strip is used, which is fixed outside the hydraulic strap with dowels
- the elasticity of the material makes it possible to clearly install the hydraulic shutter in the design position
- the presence of ribs on the locking plane and anchors prevents the penetration of moisture into the structure
- it is used in the locations of deformation joints of monolithic reinforced concrete structures
- in particularly important constructions, it is supplemented by a U-shaped repair hydraulic spar of the PO series
- They are delivered in rolls of 25 m.p.
Material: plasticized polyvinyl chloride (PVC-p)
Color: Blue
Packaging: rolls of 20 m.
Roll length deviation, m: no more than ± 0.5
Dimensional deviations: according to KD
Shore hardness, A: 70 ± 5
Density, g / cm3: ≈ 1.4
Tensile strength, MPa: ≥10 (DIN 53455)
Elongation at break,%: ≥ 275
Temperature resistance, ° C: from -35 ° C to 70 ° C
Chemical resistance:
- from constant exposure to water and sewage;
- from short-term exposure to inorganic alkalis and acids of low concentration, mineral oils.
UV resistance: not stable
Service life: 25 years
Hydroshponka ND-r 200 is an ideal solution for sealing deformation joints at the junction of concrete and metal structures. Due to its uniqueness, it is used in various objects, including buildings, foundations, underground parking lots, tunnels and canals. Our hydraulic key is easily mounted on an existing structure and securely fixed with a metal strip and dowels. Its material has high elasticity, which allows you to precisely install it in accordance with the project. The product has ribs on the closing plane and anchors, which effectively prevent moisture from entering the structure. Hydro-shponka is used in special places where there are deformation joints of monolithic reinforced concrete structures. For particularly important projects, we recommend supplementing the installation of our hydraulic key with a U-shaped repair hydraulic key of the Po series to guarantee maximum reliability and durability. Hydrosponge is supplied in bays 20 meters long, which provides a sufficient supply for waterproofing works.
Hydroshponka ND-R 200 is a reliable and effective solution for sealing deformation joints when connecting concrete and metal structures. It is used in various construction projects - from buildings and foundations to underground parking lots, tunnels and canals. Ease of installation is the main advantage of this hydraulic key. It is easily attached to the existing structure and is fixed with the help of a metal strip and dowels. The material of the hydro-pin has high elasticity, which allows you to precisely set it in a given position. Ribs on the locking plane and anchors protect the structure from moisture penetration. Hydro-shponka ND-R 200 is ideal for places where deformation joints of monolithic reinforced concrete structures are located. It is important to note that for particularly important structures it is recommended to use also a U-shaped repair hydraulic key from the po series. It is also worth noting that the hydroshponka is supplied in convenient rolls of 20 meters in length. See for yourself its reliability and quality!
How to install a hydraulic key?
The hydraulic dowel is installed in the design position so that the middle of the hydraulic dowel is in the center of the intended seam.
Fastening is carried out directly to the formwork. Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor. The fastening step is 200-300 mm, symmetrically on both sides. Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire. The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Ten. The temperature of adhesion is about 200 ° C (chosen experimentally). To connect the keys by the "cold" method, glue is used, for example, a one-component pasty glue based on
silane-modified Innoellast polymer.
The unique hydraulic key ND - R 200 from Protex is a reliable solution for sealing deformation joints when connecting to concrete and metal structures. It is excellent for monolithic construction, including buildings, foundations, underground parking lots and tunnels. With the help of a metal strip that can be fixed to the outside of the hydraulic key with dowels, we ensure a reliable fastening of the hydraulic key. Its elasticity allows you to precisely install it in the design position. The presence of ribs on the locking plane and anchors prevents moisture from entering the structure. Our hydraulic key ND-R 200 is ideal for places where there are deformation joints of monolithic reinforced concrete structures. And in particularly important cases, we recommend additionally using our U-shaped repair hydraulic key of the po series. The product is delivered in convenient rolls of 20 meters long, which ensures convenience and economy in the work process. Don't miss the opportunity to provide reliable waterproofing and protection of your structures with the ND-r 200 hydraulic dowel from Protex.
Delivery methods:
- Delivery by courier in Kyiv (1-3 working days, cost according to the carrier's tariffs);
- Address delivery by Nova Poshta Courier (1-3 working days, cost according to the carrier's tariffs);
The cost of delivery is based on the carrier's tariffs - Nova Poshta in Ukraine (1-3 working days, cost according to the carrier's tariffs);
The cost of delivery is based on the carrier's tariffs - Pickup from the Protex warehouse — Free;
(The address of the warehouse: Kyiv, 9 Pshenychna Street. The goods can be received from 9:00 a.m. to 5:00 p.m., from Monday to Friday.)
Payment methods:
- Postpaid "Nova Poshta"
The buyer-recipient of the parcel pays a commission of 2% + UAH 20 from the amount of the order. - Payment by bank card (Privatbank 4246 0010 3027 1724)
(Recipient: Fedchenko Svitlana Serhiivna) - Payment by details (PrivatBank)
IBAN account: (UA103052990000026000005026855)
Recipient: FOP Fedchenko Svitlana Serhiyivna,
EDRPOU: 2745422924