Internal hydraulic key for expansion joints VD 200, PVC, bay 20 m, blue
Internal hydraulic key for expansion joints VD 200, PVC, bay 20 m, blue
Internal hydraulic plug for sealing and waterproofing deformation movable joints VD 200, PVC, bay 20 m, blue color
Hydro-shponka VD 200 is used for sealing and waterproofing movable joints during monolithic construction of buildings, including foundations, underground parking lots, tunnels, canals, etc. mounted directly on the formwork sheet. It is used in hydraulic structures-reservoirs, canals, dams, pools, etc., as well as for waterproofing the joints of bases, foundations, tunnels, multi-level parking lots and other underground structures. It is made of plasticized polyvinyl chloride PVC-p
- allows you to reliably embed it in a concrete structure
- the presence of ribs on the closing plane protects the penetration of moisture inside the structure
- the presence of a deformable section allows you to perceive deformations of reinforced concrete structures without breaking the tightness
- used for sealing between two concrete structures
- in particularly important structures, it is supplemented with an internal hydraulic key
- can be used in structures with special requirements to ensure tightness
- withstands high water pressure inside and outside
- suitable for all types of structures
- hydroshponka is supplied in rolls of 20 m. p
Material | Plasticized polyvinyl chloride (PVC-n) |
Color | Blue |
Packaging | Rolls of 20 m. p. |
Roll length deviation, m, no more | ± 0.5 |
Size deviations | According to KD |
Shore hardness, A | 70 ± 5 |
Density, g / cm3 | ≈ 1.4 |
Tensile strength, MPa | ≥10 (DIN 53455) |
Elongation at break, % | ≥ 275 |
Heat resistance, ° C | from -35 ° C to 70 ° C |
Chemical resistance | - from constant exposure to water and sewage; - from short-term exposure to inorganic alkalis and low-concentration, mineral acids |
UV resistance | Not stable |
Term of operation | not less than 25 years |
Material: plasticized polyvinyl chloride (PVC-p)
Color: Blue
Packaging: rolls of 20 m. p.
Roll length deviation, m: no more than ± 0.5
Dimensional deviations: according to KD
Shore hardness, A: 70 ± 5
Density, g / cm3: ≈ 1.4
Tensile strength, MPa: ≥10 (DIN 53455)
Elongation at break,%: ≥ 275
Temperature resistance, ° C: from -35 ° C to 70 ° C
Chemical resistance:
- from constant exposure to water and sewage;
- from short-term exposure to inorganic alkalis and acids of low concentration, mineral oils.
UV resistance: not stable
Service life: 25 years
Installation procedure and rules:
- The hydraulic key is installed in the design position, so that the middle of the hydraulic key is in the center of the expected deformation seam.
- Fastening is carried out directly to the formwork.
- Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor.
- The fastening step is 200-300 mm, symmetrically on both sides.
- Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire.
- The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Ten.
- The temperature of adhesion is about 200 ° C (chosen experimentally).
- To connect the keys by the "cold" method, glue is used, for example, a one-component pasty glue based on InnoElas silane-modified polymer
The Protex VD 200 water seal is an ideal solution for sealing and waterproofing movable joints during the construction of buildings.
Made of high-quality plasticized polyvinyl chloride PVC-p, it perfectly copes with the sealing of foundations, tunnels, underground parking lots, canals and other structures.
Our hydraulic key has many advantages that make it indispensable in the construction industry.
Its presence of ribs on the closing plane prevents the penetration of moisture inside the structure, ensuring durability and reliability.
Thanks to the deformable area, the hydraulic key easily adapts to the deformations of reinforced concrete structures without breaking the tightness.
It is also ideal for sealing between two concrete structures.
Our water lock can also be supplemented with an internal water lock in particularly important structures to ensure maximum tightness.
It can be successfully used in constructions with special requirements, where reliable tightness is critical. The product withstands high water pressure both inside and outside, which makes it ideal for any type of construction.
Protex ВD 200 hydraulic plug is supplied in rolls of 20 meters long, which provides sufficient length for any construction project. Do not miss the opportunity to get high-quality waterproofing from our reliable and durable Protex VD 200 waterproofing.
How to install a hydraulic key?
- The hydraulic dowel is installed in the design position so that the middle of the hydraulic dowel is in the center of the intended seam.
- Fastening is carried out directly to the formwork.
- Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor.
- The fastening step is 200-300 mm, symmetrically on both sides.
- Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire.
- The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Tena.
- The temperature of adhesion is about 200 ° C (chosen experimentally).
- To connect the pins by the "cold" method, glue is used, for example, a one-component pasty glue based on
- silane-modified Innoellast polymer.
Protex Hydroshponka VD 200, bay 20 m: ensure reliable sealing and waterproofing of moving joints during the construction of your buildings with the help of Hydroshponka VD 200 from Protex.
This versatile product is ideal for monolithic construction, including foundations, underground parking lots, tunnels, canals and more. Mounted directly on formwork sheets, providing maximum protection.
Due to the presence of ribs on the closure plane,
Hydro-shponka VD 200 prevents the penetration of moisture inside the structure, ensuring durability and reliability.
Also, the presence of a deformable area allows Hydroshponke VD 200 to perceive deformations of reinforced concrete structures without breaking the tightness. Our hydraulic spigots are used to seal between two concrete structures and can be used in particularly important projects where special tightness is required.
They support high water pressures both internally and externally, making them an ideal choice for various types of structures. The VD 200 Hydro-Tip comes in 20 meter rolls, providing enough material for your project.
Delivery methods:
- Delivery by courier in Kyiv (1-3 working days, cost according to the carrier's tariffs);
- Address delivery by Nova Poshta Courier (1-3 working days, cost according to the carrier's tariffs);
The cost of delivery is based on the carrier's tariffs - Nova Poshta in Ukraine (1-3 working days, cost according to the carrier's tariffs);
The cost of delivery is based on the carrier's tariffs - Pickup from the Protex warehouse — Free;
(The address of the warehouse: Kyiv, 9 Pshenychna Street. The goods can be received from 9:00 a.m. to 5:00 p.m., from Monday to Friday.)
Payment methods:
- Postpaid "Nova Poshta"
The buyer-recipient of the parcel pays a commission of 2% + UAH 20 from the amount of the order. - Payment by bank card (Privatbank 4246 0010 3027 1724)
(Recipient: Fedchenko Svitlana Serhiivna) - Payment by details (PrivatBank)
IBAN account: (UA103052990000026000005026855)
Recipient: FOP Fedchenko Svitlana Serhiyivna,
EDRPOU: 2745422924