Product code: 0193
For sealing horizontal and vertical joints in concrete structures
InnoElast Type 1 (grey) — a one-component paste-like adhesive based on a silane-modified polymer (SPPO = silanterminated polypropylene oxide), which acquires elasticity and hardens in a humid environment. It is a one-component adhesive and sealing compound based on a silane-modified polymer that hardens into an elastic product upon contact with moist air. For sealing horizontal and vertical joints in concrete structures.
Specifications:
Application areas:
Surface preparation:
Subsequent processing:
At the time of formation of a stable surface film
The InnoElast® sealant must be protected from moisture.
If in the future it is planned to apply paint and varnish
coverage, we recommend conducting your own tests
due to the wide variety of possible systems
coatings. InnoElast® type 2 is suitable for applying paint
in accordance with DIN 52452, part 4.
Consumption and minimum dimensions of seams:
When sealing joints in accordance with DIN 18540
it is necessary to observe a sufficient width (≥ 5 mm) and
the depth (≥ 10 mm and ≥ ½ width) of the seam.
Consumption: 1 ml/cm3
Volume [ml/m]=w×d×100 (in cm)
Instructions:
InnoElast® sealant is moisture-proof, that is
high temperatures or high absolute humidity
the ambient air accelerates the curing process (thereby
thereby reducing the open exposure time
sealing material), and low — slow it down.
Preheating of the material at temperatures
below 5°C facilitates application.
Hardened residues can be removed mechanically with
using a scraper or a spatula.
Consistency : pasty
Color : Grey
Odor : none
Special density : 1.6 g/cm3
Density * : approx. 25 (Shore Type A)
Max. deformation : 25 %
Film formation ** : approx. 2 - 3 hours
Curing rate** : approx. 2 mm/24 hours
Temperature.Laying mode : -3°C - 40°C (concrete body temperature)
Temperature resistance : approx. -40 to 110°C / short-termimpact. up to 220°C
Packaging: in tubes of 600 ml (900 g)
Storage: in a cool and dry place, in the original packaging for up to 12 months
The surface must be durable and stable, free of dust, grease, oils and other materials that impair adhesion. The surface may be wet, but it should not be wet and have a visible film of moisture.
Suitable for application on concrete and other mineral building materials, as well as drywall, wood, metal, PVC, ceramics, bitumen, etc.; in case of doubt, we recommend conducting preliminary tests.
Application:
InnoElast® is applied directly to the surface using a squeeze gun. No primer is required for suitable surfaces.
When sealing joints, it is necessary to observe a sufficient width (≥ 5 mm) and depth (≥ 10 mm and ≥ ½ width) of the seam. In order to avoid 3-sided adhesion to the base of the joint, it is necessary to lay a suitable filling cord or a strip of polyethylene in the joint. It is recommended to glue the edges of the joint with adhesive tape. When filling the seam with sealing material, it is necessary to avoid the formation of voids and bubbles. By pressing and smoothing, ensure good adhesion to the sides of the seam. As a smoothing agent, pure liquid soaps (not diluted with water), such as dish detergent, are used. The adhesive tape should be removed immediately after smoothing. The maximum thickness of the sealing material layer applied in one operation should not exceed 5 cm.
When used as an adhesive, InnoElast® is evenly applied to the surface to be bonded and distributed with a notched trowel in a layer from 1 to 2 mm thick. To avoid voids and bubbles in the joint, you need to press the sealant tightly over its entire surface. Gluing a large-sized surface with InnoElast® requires a moisture-permeable substrate. For impermeable surfaces, we recommend using FlächenElast® adhesive and sealant with artificial hardener.
To adhere the ProElast® film tightly, follow the application instructions in the ProElast® System passport. In case of doubt during surface preparation and application, we recommend conducting a preliminary test.
At the time of formation of a stable surface film
The InnoElast® sealant must be protected from moisture.
If you plan to apply paintwork in the future
coverage, we recommend conducting your own tests
due to the wide variety of possible systems
coatings. InnoElast® type 2 is suitable for applying paint
in accordance with DIN 52452, Part 4.
Consumption and minimum seam sizes:
When sealing joints in accordance with DIN 18540
a sufficient width (≥ 5 mm) must be observed and
the depth (≥ 10 mm and ≥ ½ width) of the seam.
Consumption: 1 ml/cm3
Volume [ml/m]=w×d×100 (in cm)
InnoElast® sealant is moisture-proof, that is
high temperatures or high absolute humidity
the ambient air accelerates the curing process (thereby
thereby reducing the open exposure time
sealing material), and low ones slow it down.
Preheating of the material at temperatures
below 5°C facilitates application.
Hardened residues can be removed mechanically with
using a scraper or a spatula.
To ensure the waterproofness of working seams in foundations and walls
Universal construction film
For sealing of places of passage of engineering communications
Mounting profile for secure fastening of bentonite cord
To ensure the waterproofness of working seams in building structures
For sealing holes in building structures
To ensure the waterproofness of working seams in underground construction
© "Protex-S" LLC2021 | Website created by MD Design