_244_1792747146.png)
There is a rule in construction: the quality of the finishing coating depends on the preparation of the substrate by 80%. When it comes to protecting a building from moisture, the key element of this preparation is the ADW Izoplast R bitumen primer. This one-component primer based on organic solvents is a recognized standard in industrial and residential construction.
.png)
By its structure, ADW Izoplast R is a highly fluid bitumen-rubber emulsion. Unlike thick mastics, the primer has an extremely low viscosity and high penetration ability.
When applied to a porous mineral surface (concrete, brick or cement screed), it deeply penetrates the top layer of the base. After the solvent dries, pure bitumen remains inside the pores, which:
— Binds dust and microparticles, transforming a loose surface into a monolithic base.
— Clogs micropores, blocking capillary pathways for moisture penetration.
— Creates an adhesive film that is identical in chemical composition to coating mastic or roofing felt, guaranteeing perfect adhesion of materials to each other.
Scope of application: from foundations and roofs to fences and bridges
1. Preparation of foundations and basements: A mandatory stage of cold priming of cement concrete bases before applying a waterproofing compound, for example, bitumen mastic Izoplast B.
2. Arrangement of roofing systems: Priming of reinforced concrete slabs or cement screeds before applying roofing felt or repairing bitumen roofs.
3. Lightweight self-contained waterproofing: It can be used to create «lightweight» waterproofing coatings for underground structures against capillary moisture at low water load (in 2–3 layers).
4. Anti-corrosion protection of metal: Creation of a thin insulating layer on metal structures and elements (e.g. bridges) and galvanized steel.
5. Wood impregnation: Deep impregnation of wooden surfaces and particleboard to prevent rot, mold, fungi and damage by insect pests, as well as to protect wooden elements (e.g. fences or posts) buried in the ground.
.png)
Izoplast R primer technology card
The approximate consumption of IZOPLAST R when applied to concrete surfaces and for the first layer of anti-corrosion protection on metal surfaces is from 0.3 l/m² to 0.6 l/m². When performing anti-corrosion protection of metal surfaces, the approximate consumption of IZOPLAST R is from 0.2 l/m² to 0.5 l/m².
Drying time of one layer: no more than 6 hours.
Conditions of use: All work using IZOPLAST R should be carried out in good weather, at an ambient temperature of +5°C to +30°C. Do not carry out work in strong winds and precipitation.
Transportation and storage: Store in tightly closed original packaging in a place inaccessible to children, protected from direct sunlight, away from heat sources and open flames.
Notes and warnings: IZOPLAST R cannot be used inside residential and public buildings and other premises with constant human presence, as well as in the food industry. The material must not come into direct contact with food and drinking water.
Warranty period: 12 months from the date of manufacture.
.png)
Izoplast R primer application technology
To get maximum efficiency from ADW Izoplast R primer, follow the technological process:
Substrate preparation: The surface must be dry, clean of rust, old paint, grease, dirt, etc.
Mixing: Before use, the primer must be thoroughly mixed throughout the entire volume of the bucket. The material is completely ready for use.
Application: Apply cold, by spreading with a brush, roller or spray, avoiding puddles. The next layer of IZOPLAST R primer can be applied after the previous layer has dried (after 6 hours).
Number of layers:
- — on concrete surfaces in one layer when priming under mastic or roofing felt;
- — two to three layers when applying moisture-proof coatings;
- — at least two layers when applying anti-corrosion protection to metal surfaces of bridge equipment.
ADW Izoplast R bitumen primer is an inexpensive but critically important investment in the reliability of the building and the creation of an ideal base for the long service life of waterproofing systems. As the official importer of the ADW Izoplast brand in Ukraine, we guarantee 100% originality of the European product, constant availability in stock and the best price on the market.
