Product code:  0083 Producer: Protex (Україна)

External hydraulic dowel for working seams HP 200 PVC, blue, bay 20 m

7540 Product code:0083 Producer: Protex (Україна)

External hydraulic dowel for working seams HP 200 PVC, blue, bay 20 m

External hydraulic plug for sealing and waterproofing working process seams HP 200 PROTEX PVC, blue, bay 20 m

7540 uah / roll

+38 067 414 61 38
0 800-400-212

HP 200 PROTEX hydro-shponka is used for sealing and waterproofing technological seams during monolithic construction of buildings, including foundations, underground parking lots, tunnels, canals, etc. are mounted directly on the formwork sheet from the side of the expected water pressure. They are made of plasticized polyvinyl chloride PVC-p.

  • the form allows you to reliably embed it in a concrete structure
  • the presence of ribs on the closing plane protects the penetration of moisture inside the structure
  • used when concreting of monolithic reinforced concrete structures is interrupted
  • in particularly important structures, it is supplemented with an internal hydraulic key
  • can be used in structures with special requirements to ensure tightness
  • withstands high water pressure from the outside
  • ease of installation, does not require changing the reinforcing frame
  • suitable for all types of structures
  • Supplied in rolls of 20 m. n;

 

Material Plasticized polyvinyl chloride (PVC-n)
Color Blue
Packaging Rolls of 20 m. p.
Roll length deviation, m, no more ± 0.5
Size deviations According to KD
Shore hardness, A 70 ± 5
Density, g / cm3 ≈ 1.4
Tensile strength, MPa ≥10 (DIN 53455)
Elongation at break, % ≥ 275
Heat resistance, ° C from -35 ° C to 70 ° C
Chemical resistance - from constant exposure to water and sewage;
- from short-term exposure to inorganic alkalis and low-concentration, mineral acids
UV resistance Not stable
Term of operation not less than 25 years

 

Material: plasticized polyvinyl chloride (PVC-p)
Color: Blue
Packaging: rolls of 20 m. p.
Roll length deviation, m: no more than ± 0.5
Dimensional deviations: according to KD
Shore hardness, A: 70 ± 5
Density, g / cm3: ≈ 1.4
Tensile strength, MPa: ≥10 (DIN 53455)
Elongation at break,%: ≥ 275
Temperature resistance, ° C: from -35 ° C to 70 ° C
Chemical resistance:

- from constant exposure to water and sewage;
- from short-term exposure to inorganic alkalis and acids of low concentration, mineral oils.

UV resistance: not stable
Service life: 25 years

Installation procedure and rules:

  • The hydraulic key is installed in the design position, so that the middle of the hydraulic key is in the center of the expected deformation seam.
  • Fastening is carried out directly to the formwork.
  • Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor.
  • The fastening step is 200-300 mm, symmetrically on both sides.
  • Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire.
  • The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Ten.
  • The temperature of adhesion is about 200 ° C (chosen experimentally).
  • To connect the keys by the "cold" method, glue is used, for example, a one-component pasty glue based on InnoElas silane-modified polymer

HP 200 hydro-shponka from Protex is the most reliable and durable solution for sealing and waterproofing technological seams in monolithic construction.

With its help, you will be able to ensure absolute protection of buildings, foundations, underground parking lots, tunnels, canals and much more.

Made of plasticized polyvinyl chloride PVC-p, our hydroshponka provides reliable tightness and protection against moisture.

Its special shape allows it to be easily and reliably embedded in a concrete structure, and the presence of ribs on the closing plane prevents the penetration of moisture into the structure.

This hydraulic key is ideal for use during the interruption of concreting of monolithic reinforced concrete structures.

In addition, in particularly important structures, it can be supplemented with an internal hydraulic key to ensure even greater tightness.

Our hydraulic key can withstand high water pressure from the outside and is suitable for all types of structures.

The advantage of its use also lies in the ease of installation - it does not require changing the reinforcing frame and is easily mounted directly on the formwork sheet.

Protex hydraulic anchor HP 200 hydraulic anchor is supplied in convenient rolls of 20 meters long, which makes it easy and economical to use in any construction project.

Safety, reliability and ease of use - that's what makes our hydraulic key the best choice for sealing and protecting your structures.

How to install a hydraulic key?

  • The hydraulic dowel is installed in the design position so that the middle of the hydraulic dowel is in the center of the intended seam.
  • Fastening is carried out directly to the formwork.
  • Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor.
  • The fastening step is 200-300 mm, symmetrically on both sides.
  • Additional fastening is carried out in the same way to the reinforcing frame with a knitting wire.
  • The spigot is connected by welding, by heating the ends of the spigot in a special conductor (for each spigot – an individual conductor) or with the help of an industrial hair dryer or a flat Tena.
  • The temperature of adhesion is about 200 ° C (chosen experimentally).
  • To connect the pins by the "cold" method, glue is used, for example, a one-component pasty glue based on
  • silane-modified Innoellast polymer.

Build your structure with the help of Protex Hydroshponka HP 200!

This reliable product is ideal for sealing and waterproofing technological joints in monolithic construction of buildings, including foundations, underground parking lots, tunnels, canals and much more.

We used only high-quality materials, such as plasticized polyvinyl chloride PVC-p, to ensure maximum tightness.

Our hydraulic key has a special shape that easily integrates into the concrete structure, and the ribs on the locking plane prevent moisture from penetrating inside.

It can be used even during a break in the concreting of monolithic reinforced concrete structures, and in particularly important cases, it is recommended to additionally use an internal hydraulic key to ensure complete tightness.

Our hydraulic key is able to withstand high water pressure from the outside, which makes it an ideal choice for structures with special requirements for tightness.

Its ease of installation does not require changes in the reinforcing frame and it is suitable for all types of structures. The product is supplied in convenient 20 meter long rolls.

Rebuild your structure with a reliable and high-quality hydraulic key Protex Hydraulic key HP 200!

Delivery methods:

  • Delivery by courier in Kyiv (1-3 working days, cost according to the carrier's tariffs);
  • Address delivery by Nova Poshta Courier (1-3 working days, cost according to the carrier's tariffs);
    The cost of delivery is based on the carrier's tariffs
  • Nova Poshta in Ukraine (1-3 working days, cost according to the carrier's tariffs);
    The cost of delivery is based on the carrier's tariffs
  • Pickup from the Protex warehouse — Free;
    (The address of the warehouse: Kyiv, 9 Pshenychna Street. The goods can be received from 9:00 a.m. to 5:00 p.m., from Monday to Friday.)

Payment methods:

  • Postpaid "Nova Poshta"
    The buyer-recipient of the parcel pays a commission of 2% + UAH 20 from the amount of the order.
  • Payment by bank card (Privatbank 4246 0010 3027 1724)
    (Recipient: Fedchenko Svitlana Serhiivna)
  • Payment by details (PrivatBank)
    IBAN account: (UA103052990000026000005026855)
    Recipient: FOP Fedchenko Svitlana Serhiyivna,
    EDRPOU: 2745422924

Супутні товари