Hydroshponka P-3 for sealing and waterproofing movable joints, bay 20 m, gray

Material: plasticized polyvinyl chloride (PVC-p)
Color: Gray
Packaging: rolls of 20 m.
Roll length deviation, m: no more than ± 0.5
Dimensional deviations: according to the technical specifications
Shore hardness, A: 70 ± 5
Density, g/cm3: ≈ 1.4
Tensile strength, MPa: ≥10 (DIN 53455)
Elongation at break,%: ≥ 275
Temperature resistance, °C: from -35 °C to 70 °C
Chemical resistance:

- from constant exposure to water and wastewater;
- from short-term exposure to low-concentration inorganic alkalis and acids, mineral oils.

UV resistance: not resistant
Service life: 25 years

Get used to flawless sealing and reliable waterproofing with the Protex P-3 hydrostop. This indispensable tool is used to fill moving joints in monolithic underground and buried structures, providing reliable protection. The Protex P-3 hydrostop is ideal for hydraulic structures such as tanks, canals, dams and pools, and also provides reliable waterproofing of joints in foundations, foundations, tunnels and even multi-level parking lots. Made of plasticized polyvinyl chloride PVC-p, the hydrostop has a unique shape that makes it easy to install in the design position. Just put the key on a sheet of expanded polystyrene and you're done! It is important to note that the Protex P-3 hydrostop has ribs on the locking plane that prevent moisture from penetrating into the structure. It is also used in places where expansion joints of monolithic reinforced concrete structures are located. If you are working with particularly important structures, it is recommended to supplement the Protex P-3 waterstop with an internal or lower external waterstop for maximum effect. Do not worry about water pressure - the Protex P-3 waterstop easily withstands it both inside and outside. This is a great solution for all types of structures, ideal for your project. The Protex P-3 waterstop is supplied in coils of 25 meters, providing you with enough material to implement your tasks.

How to install a hydraulic wedge?

The hydraulic key is installed in the design position so that the middle of the hydraulic key is in the center of the intended seam.
Fastening is carried out directly to the formwork. Holes for fastening are allowed to be made only in the extreme zone of the hydraulic dowel, behind the extreme anchor. The fastening step is 200-300 mm, symmetrically on both sides. Additional fastening is also carried out to the reinforcing frame with a knitting wire. The dowel is connected by welding, by heating the ends of the dowel in a special conductor (for each dowel - an individual conductor) or using an industrial hair dryer or flat heating element. The soldering temperature is about 200 ° C (selected experimentally). To connect the dowels by the "cold" method, glue is used, for example, a one-component paste-like glue based on
silane-modified polymer Innoellast.

P-3 waterstop: powerful protection and reliable waterproofing for your construction project. Our P-3 waterstops are designed specifically for sealing and waterproofing moving joints in buried and underground structures. You can be sure of their effectiveness and reliability. The use of P-3 waterstops is suitable for various hydraulic structures, such as tanks, canals, dams, pools, and many others. They are also ideal for waterproofing joints in foundations, tunnels, multi-level parking lots, and other underground structures. Made of plasticized polyvinyl chloride PVC-P, our waterstops provide strength and durability that you can trust. The "P" shape of the waterstop makes it easy to install it in the desired position, for example, using a sheet of expanded polystyrene. This ensures accurate and reliable installation in the design position. The presence of ribs on the locking plane provides reliable protection against moisture penetration into the structure. You can be sure that your structure will be protected from moisture and potential damage. P-3 waterstops are used in the locations of expansion joints of monolithic reinforced concrete structures. They can also be supplemented with an internal or lower external waterstop for especially important structures. Our P-3 waterstops are resistant to small water pressure both from the outside and from the inside. This provides additional safety and protection for your structure. Convenient provision in coils of 25 m.p. allows you to simply and easily use our P-3 waterstop for any type of structure. Choose a P-3 waterstop and ensure reliable waterproofing for your construction project.

• texkarta-gidroshponki-p-43828042