EPDM-ProElast 1.0=200mm membrane

Product code: 0204

For external sealing of seams and joints at construction sites

from 400,00
uah
x
m.p.
=
from 400,00 uah
Wholesale price from 360,00 uah from 200 m.p.

There will be a more favorable price offer for you. Please leave a request and our managers will make an individual calculation for you.

400

The system of protection of seams from water — ProElast System (ProElast-System) is a registered system designed to seal working seams, seams of intentional rupture and deformation seams from soil moisture, water without pressure, periodically rising water and water under pressure. The system consists of a universal one-component InnoElast adhesive and a 1 mm thick printed EPDM membrane ProElast. Both components are universal and can be used for a wide variety of tasks:

  • joints in precast concrete structures;
  • joints in monolithic concrete structures;
  • when sealing basements;
  • expansion joints.

Advantages:

  • the system is resistant to positive and negative water pressure
  • possibility of laying on wet surfaces
  • laying at temperatures up to — 3 ° C
  • good compatibility with old bitumen waterproofing
  • high chemical and microbiological resistance
  • wear resistance
  • absence of solvents in the composition (environmentally friendly product)
  • UV resistance

Due to its high resistance to UV radiation, the system can be used on high-rise construction sites. Mechanical fastening of the membrane or its edges is not required.

The system of sealing seams from water is used to seal working seams, seams of directional rupture and deformation seams from soil moisture, from water without pressure, from periodically rising water, as well as from water under pressure.

This system is resistant to UV rays and can be used in multi-storey high-rise construction. There is no need for mechanical fastening of the membrane edges with flanges or other mechanical fasteners.

The Proelast membrane is a printed membrane based on vulcanized ethylene propylene rubber EPDM (ethylene-propylene-diene-copolymer) for sealing joints in concrete structures.

InnoElast is a one—component adhesive and sealing compound based on a silane-modified polymer that hardens into an elastic product upon contact with moist air, used for sealing horizontal and vertical joints in concrete structures. It has the ability to self-leveling (self-leveling), as well as high chemical resistance, which allows using this product in horizontal seams as a durable, elastic filler for temperature, technological and false seams with a maximum deformation of up to 10%.

Sealing of expansion joints:

The system can be used as a sealing of deformation seams with an initial width of up to 20mm, subject to rarely repeated slow deforming loads, as well as in the seams of impassable parts of structures. Simultaneous change of the seam width and its shift should not exceed 50% of the original joint width.

Before laying a system with a membrane width of 300 mm or more, it is necessary to ensure the protection of the sealant, for example, by using a backfill or ensuring the distance to the formwork. The installation of the system takes place in the same way as when sealing the working seams. The inner and outer corners are sealed with membrane segments prepared in advance for them. The system is glued to the entire surface of the corner. It is necessary to pay attention so that in the joint area there is no gluing of the adhesive mass with the parts of the backfill.

Special cases of application of the system:

Deformation and separation seams can be performed by analogy with the usual way of arranging the transition of the seam, with the additional use of a round scoring profile. When laying the material on a surface made of brick, it should be pre-treated with a special sealing sludge (application in two layers). The holes for laying pipes or cables must be protected by a sealing cuff and provided with a funnel-shaped connecting element.

attention:

InnoElast does not contain solvents, silicones and isocyanates. Before starting to work with the material, it is necessary to familiarize yourself with the recommendations and safety instructions described in the safety data sheet. When working with materials that are not subject to mandatory labeling but are chemical products, appropriate precautions must be observed. InnoElast Typ contains aminosilanes that can cause allergic reactions.

 

Related materials