Hydroflex 21 glue-repair mixture
Epoxy two-component solvent-free adhesive for fixing deformation tapes.
Tenalux 131M elastic one-component polyurethane sealant for joints, 600 ml file package.
Tenalux 131M elastic one-component polyurethane sealant for construction joints, grey, 600 ml file package.
340,00 uah
x
шт.
=
TENALUX 131 M is a ready-to-use one-component sealant, developed on the basis of MS polymer (silane modified polymer) in the form of a gray thixotropic mass. It is used for sealing joints, seams and cracks on horizontal, vertical and inclined building surfaces with a maximum deformation of ± 25% under increased regular and irregular mechanical loads. It has a high level of adhesion to various surfaces of building materials, as well as good strength and deformation characteristics after polymerization.
Application:
- sealing joints of industrial floors
- sealing joints of vertical and inclined construction structures
- sealing joints in horizontal building structures
- sealing of expansion joints with a maximum deformation of ± 25% under regular and irregular mechanical loads
Appearance - Gray thixotropic mass, other colors are possible on request
The type of polymer is a single-component MS polymer, cold curing under the influence of air moisture
Packaging - Packed in tubes of laminated plastic with a capacity of 600 ml
The warranty period of storage is 12 months in unopened, complete factory packaging in dry warehouses at a temperature of no more than 30 °C.
Sealing properties - The formation of a surface film for ≈ 20 minutes at 23 °C and a relative humidity of 50 %
The curing rate is 3 to 4 mm/day at 23 °C and a relative humidity of 50 %
Shrinkage - ≤ 1 %
Density - ≈ 1.5 kg/liter
Return deformation
≥ 70 % (ISO 7389)
Strength characteristics (on concrete seam samples)
It is supplied in cardboard boxes equipped with labels, one box contains 15 tubes..
GOST 21751-76
(ISO 8339)
• conditional tensile strength
≥ 1.8 MPa
≥ 1.3 MPa
• elongation at the moment of rupture
≥ 400 %
≥ 200 %
• modulus of elasticity at 100 % elongation
0.7 to 0.9 MPa
> 0.4 MPa
Shore hardness A - 40 ± 2 (ISO 868)
The application temperature range is from 1 °C to 50 °C
The operating temperature range is from - 50 °C to 70 °C
Applicable seams (joints)
The permissible deformation is ± 25 %
Seam depth - from 5 to 20 mm
Seam width - from 10 to 40 mm
The ratio of the width to the depth of the seam is 2:1
How to apply the sealant correctly?
The surface must be solid, clean and dry. Therefore, before applying the sealant, the treated surface must be cleaned of all impurities that reduce adhesion. If necessary, all surface defects, cracks and chips should be leveled using TEKNO repair compounds.
The sealing compound is applied manually using special syringes (pistols). The sealant cures as a result of a chemical reaction with air moisture. To prevent the sealant from coming into contact with the structural elements of the joints, it is necessary to use a polyethylene foam tourniquet or anti-adhesive compounds.
How does the deformation seam work?
To prevent the formation of a third plane of contact between the sealant and the structural elements of the seam, it is always necessary to use anti-adhesive compounds or sealing gaskets, such as, for example, a bundle of foamed polyethylene. To limit the depth of the sealant layer, achieve the recommended ratio of width and depth of the sealant, as well as to reduce material consumption, it is recommended to select the size of the sealing gasket taking into account the actual width of the seam. In addition, the use of cellular sealing materials reduces heat loss and improves sound insulation performance. It is necessary to follow the recommendations for the optimal width and depth of the seam for this sealant. Applying a sealant layer with a thickness less than the minimum recommended leads to a decrease in the durability of sealing the seam. Exceeding the maximum recommended thickness of the sealant layer causes high internal stresses that contribute to the appearance of cracks. Narrow seams must be enlarged with special tools to achieve the recommended width and depth. Seams that are too wide, as well as seams with a porous, fragile surface, should be treated with appropriate repair compounds.
Як правильно наносити герметик?
The surface must be solid, clean and dry. Therefore, before applying the sealant, the treated surface must be cleaned of all impurities that reduce adhesion. If necessary, all surface defects, cracks and chips should be leveled using TEKNO repair compounds.
The sealing compound is applied manually using special syringes (pistols). The sealant cures as a result of a chemical reaction with air moisture. To prevent the sealant from coming into contact with the structural elements of the joints, it is necessary to use a polyethylene foam tourniquet or anti-adhesive compounds.
How does the deformation seam work?
To prevent the formation of a third plane of contact between the sealant and the structural elements of the seam, it is always necessary to use anti-adhesive compounds or sealing gaskets, such as, for example, a bundle of foamed polyethylene. To limit the depth of the sealant layer, achieve the recommended ratio of width and depth of the sealant, as well as to reduce material consumption, it is recommended to select the size of the sealing gasket taking into account the actual width of the seam. In addition, the use of cellular sealing materials reduces heat loss and improves sound insulation performance. It is necessary to follow the recommendations for the optimal width and depth of the seam for this sealant. Applying a sealant layer with a thickness less than the minimum recommended leads to a decrease in the durability of sealing the seam. Exceeding the maximum recommended thickness of the sealant layer causes high internal stresses that contribute to the appearance of cracks. Narrow seams must be enlarged with special tools to achieve the recommended width and depth. Seams that are too wide, as well as seams with a porous, fragile surface, should be treated with appropriate repair compounds.
Related materials
PPE elastic sealing harness
For filling expansion joints in the construction of industrial floors, for filling joints in the installation of windows, doors, for filling inter-panel joints in the construction of buildings
PPE harness 6 mm elastic sealing, coil 450 meters
For filling expansion joints when installing industrial floors, for filling joints when installing windows, doors, for filling interpanel joints during the construction of buildings, a coil of 450 meters
PPE harness 8 mm elastic sealing, coil 450 meters
For filling expansion joints when installing industrial floors, for filling joints when installing windows, doors, for filling interpanel joints during the construction of buildings, a coil of 450 meters
PPE harness 10 mm elastic sealing, coil 450 meters
For filling expansion joints when installing industrial floors, for filling joints when installing windows, doors, for filling interpanel joints during the construction of buildings, a coil of 450 meters
PPE harness 15 mm elastic sealing, coil 600 meters
For filling expansion joints when installing industrial floors, for filling joints when installing windows, doors, for filling interpanel joints during the construction of buildings, a coil of 450 meters
PPE harness 20 mm elastic sealing, 2 meter lengths
For filling expansion joints when installing industrial floors, for filling joints when installing windows, doors, for filling interpanel joints during the construction of buildings, 2-meter sections
© "Protex-S" LLC2021 | Website created by MD Design