Metal hydraulic gasket for waterproofing structural working (cold) joints VB 160

Product code: 0096

Metal hydraulic shponka for waterproofing of structural working (cold) joints

450
uah
x
m.p.
=
450 uah
450

Hydraulic gasket VB-160 - Metal hydraulic gasket 120 (160) VB1 and VB2 is a galvanized metal plate with a waterproofing polymer coating on one or two sides for reliable waterproofing of joints from groundwater or pressurized water.

  • The peculiarity of this key is the possibility of sealing the seam without changing the reinforcement frame.
  • The hydraulic shutter 120 (160) VB1/VB2 is completely coated on one or both sides with a special coating.
  • The hydraulic shutter 120 (160)VB1/VB2 is supplied in rolls with a length of 20 m.
  • The special coating is protected by a protective tape divided into two parts for easy installation at the first and second stages of concreting.
  • After being placed in concrete, a special coating forms a bond with fresh concrete, sealing the structural seam from the ingress of pressurized water and groundwater.
  • The hydraulic gasket 120 (160)VB1/VB2 can be installed in concrete in all types of structural joints, for example foundation/wall, wall/wall, foundation/foundation wall/ceiling.

Application:
A typical application of the 120(160)VB1/VB2 metal hydraulic gasket is waterproofing of construction joints in concrete structures at the groundwater level.
After installation in construction joints in concrete, a special coating forms a bond with fresh concrete, which constantly seals the seam.
The 120 (160) VB1/VB2 metal hydraulic gasket is not only quick and easy to install, but also provides a reliable permanent seal even against high water pressure.

  • It is used when concreting monolithic reinforced concrete structures is interrupted
  • in particularly important structures, it is complemented by an external hydraulic gasket
  • the presence of ribs on the locking plane prevents the penetration of moisture into the structure
  • It can be used in structures with special requirements to ensure tightness
  • withstands high water pressure inside and outside
  • with ease of installation, it is suitable for all types of structures
  • It is supplied in rolls of 20 m.p.
Material: Steel St 37, galvanized
Coverage: The polymer resin is reinforced with fiber
Colour: Black
Length: 20 m
Height: 120(160) mm

Thickness:

Coating thickness:

Total thickness:

Approx. 0.6 mm

Approx. 0.15 mm

Approx. 0.9 mm

Weight: Approx. 0.56 kg/m Approx. 15.00 kg/roll
Operating range: - 20°C 90°C
Max. water pressure value: Up to 6 bar (60 m of water column)
Packaging:

Box (40 x 40 x 20 cm)1 Roll of 20m.p.

2 connecting elements (clips) – 30 pcs

48 boxes per pallet

Keeping: Dry composition, keep away from direct sunlight

Availability: in stock
Brand: Forbuild
Country of origin: Germany
Material delivery form: Bays of 20 meters each
Dimensions: 20 kg, 40x40x20 cm
Color: Grey
Weight, kg: 20 kg
Material: Galvanized steel

  • The installation is similar for 120 and 160 mm hydraulic dowels.
  • The product is delivered in a cardboard package.
  • It contains a 120 VB1/VB2 connecting sheet roll, as well as mounting brackets and clips.
  • Remove the lower half of the protective film from the special coating.
  • Place the hydraulic gasket 120 VB1/VB2 in the center of the structure on the outer reinforcement frame.
  • Install the brackets (30 pcs/roll), the hydraulic gasket and fix them on the upper reinforcing layer using knitting wire.
  • PLEASE NOTE! For the 120 VB1 water slide, the coating must face the side of the water support!
  • The depth of laying in concrete should be at least 3cm and should not be more than half the height of the sheet metal (6cm).
  • The connection of the hydraulic gasket 120 VB1/VB2 between each other must be overlapped, overlap by at least 5 cm in the connection area.
  • To do this, the upper protective film must be glued to the connected area.
  • The overlap of the hydraulic gasket 120 VB1/VB2 must be at least 5 cm.
  • Press both ends tightly.
  • There should be no dirt on the adhesive surfaces that could interfere with bonding.
  • Fix the joint with one of the connecting clips and close the protective film back onto the special coating.
  • Mounting sketch of a metal hydraulic shutter
  • The corners of the elements can be made on the construction site.
  • After concreting the foundation plate and before shuttering the walls or installing double walls, it is necessary to remove the residual protective film.

Where is a metal hydraulic gasket used?
A typical application of the 120(160)VB1/VB2 metal hydraulic gasket is the waterproofing of construction joints in concrete structures at the groundwater level.
After installation in construction joints in concrete, a special coating forms a bond with fresh concrete, which constantly seals the seam.
The 120 (160) VB1/VB2 metal hydraulic gasket is not only quick and easy to install, but also provides a reliable permanent seal even against high water pressure.

Where is a metal hydraulic gasket used?

A typical application of the 120(160)VB1/VB2 metal hydraulic gasket is waterproofing of construction joints in concrete structures at the groundwater level.
After installation in construction joints in concrete, a special coating forms a bond with fresh concrete, which constantly seals the seam.
The 120 (160) VB1/VB2 metal hydraulic gasket is not only quick and easy to install, but also provides a reliable permanent seal even against high water pressure.

Related materials