Combined hydraulic gasket for working seams KAB-150, bay 25 meters

Product code: 0095

Combined hydraulic joint for working seams KAV-150

1066
uah
x
m.p.
=
1066 uah
1066

HydroshponkaKAV 150 with a cord made of hydrophilic rubber combined for use in working and structural seams. KAB 150 key is a key with an expanding hydrophilic cord for sealing and waterproofing structural joints of concrete structures. Even at high water pressure, the combined KAB key provides waterproofing due to the expanding rubber cord and the ribbed part of the key itself. KAB key is an effective system against water penetration, and also easy to install.

  • there is no need to make a suture protrusion or change the reinforcement system
  • simple installation in a concrete structure with low labor costs
  • stability during installation due to mounting brackets
  • end heat welding joint to joint
  • small bending radius
  • reliable sealing and waterproofing are provided due to the ribbed part of the key and the expanding cord round in cross section

 

Specifications Od.vim. Vimogi
It's called the Wiglade - Without any fractures
Shore Hardness Sh 83±5
Between the cities MPa ≥8
Today, the wedding ceremony is held at rozrivi % ≥200
Place on the outlet N/mm ≥12
Behavior at low temperatures -20oC % ≥100
  • KAV tapes are successfully used in sewage treatment plants, swimming pools, reservoirs, foundations of residential buildings, etc.
  • CAV tapes effectively seal construction joints under hydrostatic pressure up to 0.2 MPa below the groundwater level with a variable level, for example, in basements or tunnels.
  • The tape is not sensitive to water pollution – alkaline and acidic.

REFERENCE DOCUMENTS

  • catalog: Sealing systems No. 1;
  • in accordance with the technical approval of IBDiM AT/2006-03-2101/2;
  • HK/W hygiene certificate/0922/01/2011 .


STORAGE/TRANSPORTATION

  • Sealing tapes should be transported on pallets to protect them from adverse weather conditions and to protect them from mechanical damage.
  • The tape should be stored in its original packaging on a flat surface. Keep away from direct sunlight.
  • When installing the key to the concrete pouring of the foundation plate of the CAV, the key is installed directly on the reinforcing bars and fixed with clips with an interval between clips of 0.5 m.
  • If the key is installed during or immediately after pouring concrete, the key must only be inserted into the freshly laid concrete, after which the concrete mixture can be compacted by vibrating in the usual mode.
  • The marking strip, located at a height of 3.0 cm from the edge of the key, serves as an installation depth control.
  • The maximum depth of immersion in concrete of the lower part of the key with an expanding profile is 4.0 cm.
  • The dowels can be connected to each other in two different ways:
  • The end heat welding of the dowels is performed using a welding axe (the expanding cord is removed and inserted back only after welding).
  • Parallel installation of overlapping dowels at a length of approximately 50 cm and at a distance of 5 cm from each other (in case of presence of water pressure, preference should be given to welding of dowels).
  • Cross and T-shaped key joints are also produced by heat welding using a welding axe or a construction hair dryer.
  • warning:
  • During installation, follow the construction safety regulations and the guidelines set out in this document.

How to connect the key to each other?

The dowels can be connected to each other in two different ways:
• End heat welding of dowels is performed using a welding axe (the expanding cord is removed and inserted back only after welding).
• Parallel installation of overlapping dowels at a length of approximately 50 cm and at a distance of 5 cm from each other (in case of presence of water pressure, preference should be given to welding of dowels).
• Cross and T-shaped key joints are also produced by thermal welding using a welding axe or a construction hair dryer.

How do I install a hydraulic shutter?

  • When installing the key to the concrete pouring of the foundation plate of the CAV, the key is installed directly on the reinforcing bars and fixed with clips with an interval between clips of 0.5 m.
  • If the key is installed during or immediately after pouring concrete, the key must only be inserted into the freshly laid concrete, after which the concrete mixture can be compacted by vibrating in the usual mode.
  • The marking strip, located at a height of 3.0 cm from the edge of the key, serves as an installation depth control.
  • The maximum depth of immersion in concrete of the lower part of the key with an expanding profile is 4.0 cm.
  • When installing the key to the concrete pouring of the foundation plate of the CAV, the key is installed directly on the reinforcing bars and fixed with clips with an interval between clips of 0.5 m.
     

Related materials