Waterproofing key HP 240, PVC, outer blue PROTEX for working seams, bay 20 m.p.

Material :  Plasticized polyvinyl chloride (PVC-p)
Color : Blue
Packaging: Rolls of 20 m.p.
Roll length deviation, m,: no more than ± 0.5
Size Deviation : According to CD
Shore hardness, A : 70 ± 5
Density, g/cm3 : ≈ 1.4
Tensile strength, MPa : ≥10 (DIN 53455)
Elongation at break, % : ≥ 275
Temperature resistance, °C : from -35°C to 70°C
Chemical resistance : 

- from constant exposure to water and wastewater;
- from short-term exposure to inorganic alkalis and low concentration acids, mineral oils.

UV resistance : Not resistant
Service life : 25 years

Installation procedure and rules:

• The hydraulic shutter is installed in the design position, so that the middle of the hydraulic shutter is located in the center of the intended deformation seam.
• The fastening is made directly to the formwork.
• Holes for fasteners are allowed to be made only in the extreme zone of the hydraulic gasket, behind the extreme anchor.
• The mounting pitch is 200-300 mm, symmetrically on both sides.
• Additional fastening is also performed to the reinforcing frame with knitting wire.
• The connection of the key is made by welding, by heating the ends of the key in a special conductor (for each key there is an individual conductor) or using an industrial hair dryer or a flat heating element.
• The temperature of the spike is about 200 ° C (selected experimentally).
• To connect the dowels by the "cold" method, glue is used, for example, a one-component paste-like glue based on the silane modified polymer InnoElas

The HP 240 PROTEX hydraulic gasket is your ideal choice for sealing and waterproofing process joints in monolithic construction of any buildings. Regardless of whether you are building a foundation, an underground parking lot, a tunnel or a canal, our hydraulic shutter will provide reliable protection.

Made of high-quality plasticized PVC-p polyvinyl chloride, our hydraulic shutter not only has excellent durability, but is also resistant to water pressure from the outside.

The installation of the hydraulic shutter is easy and simple.

Simply mount it directly onto the formwork sheet on the side where the highest water pressure is expected.

The shape of the hydraulic shutter allows it to be securely embedded in a concrete structure, and the presence of ribs on the locking plane guarantees reliable tightness.

Our hydraulic gasket is also ideal for a break in the concreting of monolithic reinforced concrete structures.

For particularly important structures, we recommend the additional use of an internal hydraulic gasket to provide maximum protection against moisture penetration.

The advantages of our hydraulic tamper are not only its reliability and durability, but also the possibility of use in structures with special requirements for tightness.

Moreover, it is suitable for all types of structures, and its long rolls of 25 m allow convenient use of the product. Do not postpone your protection from moisture for later.

Purchase the Protex HP 240 hydraulic gasket today and trust our quality and reliability.

How do I install a hydraulic shutter?

• The hydraulic shutter is installed in the design position, so that the middle of the hydraulic shutter is located in the center of the intended seam.
• The fastening is made directly to the formwork.
• Holes for fasteners are allowed to be made only in the extreme zone of the hydraulic gasket, behind the extreme anchor.
• The mounting pitch is 200-300 mm, symmetrically on both sides.
• Additional fastening is also performed to the reinforcement frame with knitting wire.
• The connection of the key is made by welding, by heating the ends of the key in a special conductor (for each key there is an individual conductor) or using an industrial hair dryer or a flat heating element.
• The temperature of the spike is about 200 ° C (selected experimentally).
• To connect the dowels by the "cold" method, glue is used, for example, a one-component paste-like glue based on
• silane modified polymer Innoellast.

The Protex HP 240 hydraulic gasket is your reliable and effective solution for sealing and waterproofing process joints in the construction of buildings.

Our hydraulic shingle is perfect for monolithic construction - from foundations to underground parking lots, tunnels, canals and much more.

It is mounted directly on the formwork sheet from the side of the expected water pressure and ensures the impermeability of the structure.

The special shape of the hydraulic shutter ensures strong embedding into the concrete structure, and the presence of ribs on the locking plane prevents moisture from entering the structure.

It is ideal for the construction of monolithic reinforced concrete structures with breaks in concreting.

If you are working on particularly important structures, you can supplement our hydraulic gasket with an internal hydraulic gasket to ensure even greater tightness.

The product can also be used in structures with special requirements.

Don't worry about the pressure of the water outside - our water bottle withstands it.

Installation is very simple and does not require changing the reinforcement cage.

The product is suitable for all types of structures.

You can purchase the Protex HP 240 Water cannon in rolls of 20 meters.

Count on our products and satisfied customers!