Internal hydraulic gasket for expansion joints VD 200, PVC, 20 m bay, blue

Material :  Plasticized polyvinyl chloride (PVC-p)
Color : Blue
Packaging: Rolls of 20 m.p.
Roll length deviation, m,: no more than ± 0.5
Size Deviation : According to CD
Shore hardness, A : 70 ± 5
Density, g/cm3 : ≈ 1.4
Tensile strength, MPa : ≥10 (DIN 53455)
Elongation at break, % : ≥ 275
Temperature resistance, °C : from -35°C to 70°C
Chemical resistance : 

- from constant exposure to water and wastewater;
- from short-term exposure to inorganic alkalis and low concentration acids, mineral oils.

UV resistance : Not resistant
Service life : 25 years

Installation procedure and rules:

• The hydraulic shutter is installed in the design position, so that the middle of the hydraulic shutter is located in the center of the intended deformation seam.
• The fastening is made directly to the formwork.
• Holes for fasteners are allowed to be made only in the extreme zone of the hydraulic gasket, behind the extreme anchor.
• The mounting pitch is 200-300 mm, symmetrically on both sides.
• Additional fastening is also performed to the reinforcement frame with knitting wire.
• The connection of the key is made by welding, by heating the ends of the key in a special conductor (for each key there is an individual conductor) or using an industrial hair dryer or a flat heating element.
• The temperature of the spike is about 200 ° C (selected experimentally).
• To connect the dowels by the "cold" method, glue is used, for example, a one-component paste-like glue based on the silane modified polymer InnoElas

The Protex VD 200 hydraulic gasket is an ideal solution for sealing and waterproofing movable joints in the construction of buildings.

Made of high-quality plasticized PVC-p polyvinyl chloride, it perfectly copes with sealing foundations, tunnels, underground parking lots, canals and other structures.

Our hydraulic shutter has many advantages that make it indispensable in the construction industry.

Its presence of ribs on the locking plane prevents moisture from entering the structure, ensuring durability and reliability.

Due to the deformable section, the hydraulic gasket easily adapts to deformations of reinforced concrete structures without breaking the tightness.

It is also ideal for sealing between two concrete structures.

Our hydraulic gasket can also be supplemented with an internal hydraulic gasket in particularly important structures to ensure maximum tightness.

It can be successfully used in structures with special requirements where reliable tightness is critically important. The product can withstand high water pressure both inside and outside, which makes it ideal for any type of construction.

The Protex VD 200 hydraulic shutter is supplied in rolls 20 meters long, which provides sufficient length for any construction project. Do not miss the opportunity to get high-quality waterproofing with our reliable and durable Protex VD 200 hydraulic gasket.

How do I install a hydraulic shutter?

• The hydraulic shutter is installed in the design position, so that the middle of the hydraulic shutter is located in the center of the intended seam.
• The fastening is made directly to the formwork.
• Holes for fasteners are allowed to be made only in the extreme zone of the hydraulic gasket, behind the extreme anchor.
• The mounting pitch is 200-300 mm, symmetrically on both sides.
• Additional fastening is also performed to the reinforcement frame with knitting wire.
• The connection of the key is made by welding, by heating the ends of the key in a special conductor (for each key there is an individual conductor) or using an industrial hair dryer or a flat heating element.
• The temperature of the spike is about 200 ° C (selected experimentally).
• To connect the dowels by the "cold" method, glue is used, for example, a one-component paste-like glue based on
• silane modified polymer Innoellast.

Protex Hydraulic gasket VD 200, bay 20 m: Ensure reliable sealing and waterproofing of movable joints during the construction of your buildings with the help of the Hydraulic gasket VD 200 from Protex.

This versatile product is ideal for monolithic construction, including foundations, underground parking lots, tunnels, canals and more. It is mounted directly on the formwork sheets, providing maximum protection.

Due to the presence of edges on the locking plane,

The VD 200 hydraulic gasket prevents moisture from penetrating into the structure, ensuring durability and reliability.

Also, the presence of a deformable section allows the VD 200 hydraulic gasket to perceive deformations of reinforced concrete structures without breaking the tightness. Our hydraulic seals are used to seal between two concrete structures and can be used in particularly important projects where special tightness is required.

They support high water pressures both inside and outside, which makes them an ideal choice for various types of structures. The VD 200 hydraulic gasket is supplied in rolls 20 meters long, providing enough material for your project.