Geotextile with needle-punched density 300 g/sq.m for drainage (Ukraine)

For use in the arrangement of drainage systems and in the agricultural sector

4 440,00
uah
x
rule.
=
4 440,00 uah
4440

Needle-punched geotextile has a large elongation coefficient, easily takes the necessary shape and has excellent filtering abilities in the longitudinal and transverse directions.

The main functions of geotextile:

  • lack of reaction with aggressive environment – not prone to mold formation, not afraid of high humidity, which allows you to protect the system from silting for many years;
  • resistant to rodents, moles, insects and other pests that can damage the integrity of the material;
  • it is environmentally safe for humans – artificial fibers buried in the ground do not emit toxic substances, therefore they do not harm the flower beds or vegetables in the beds;
  • resistance to temperature changes – fiber does not lose its properties under the influence of temperature changes from 110 ° C to -60 ° C, therefore it is in demand in any climate;
  • ease of handling due to the fabric base of the material, high strength and elasticity allow it to be quickly laid in the necessary pieces.

Scope of application:

  • Construction – in a flat roof system; for waterproofing as a reinforcing layer; when paving the road; for drainage; foundation construction.
  • In landscape design – the creation of Alpine slides; arrangement of reservoirs; under the sidewalks; construction of sports grounds and football fields.
  • In the clothing and footwear industry – as a cushioning and strengthening material.
  • In the furniture industry – as a separating and protective material.
  • In agriculture – protection of plants from weeds, frost, sun, wind
  • In drainage systems 

Type: Needle Punched
Thickness at a pressure of 2 kN/m2, mm: 1.5
Surface density, g/m2: 100
Tensile strength, kN/m: 4
Strength at 5% elongation, kN/m: 3
Application type:

Drainage;
Reinforcement;
Division;
Strengthening;
Filtration

Punching CBR, N: 500
Water throughput: 100 l/m2*sec
Water permeability at 20 kN/m2, 10*-4 m/s: 0.1
Length, m: 50
Width, m: 2
Dimensions (WxD), m: 2x50
Thickness, mm: 2.5

Laying geotextiles is a process that plays a key role in construction, especially when working with road surfaces, soil structures and landscaping.

Here are a few steps to help you install geotextiles correctly:

Surface preparation: Make sure the surface on which the geotextile will be laid is free of debris, sharp objects and stones. If necessary, carry out preparatory work, including leveling and compacting the soil.

Selection and installation of geotextiles: Select the appropriate type of geotextiles to suit your project requirements. When laying geotextiles, make sure that they are distributed evenly and without folds over the entire surface. Make sure that the geotextile is not damaged during installation.

Layering: If you need to use several layers of geotextiles, lay them in such a way that each layer overlaps the previous one by a sufficient length (usually at least 10-20 cm). This will help prevent soil penetration and maintain the integrity of the structure.

Fixation of geotextiles: It is important to ensure reliable fixation of geotextiles so that they do not move during construction work or as a result of environmental influences. To do this, you can use fasteners, pins, weights or other special devices.

Checking the installation quality: After installation is complete, check the quality of the work done. Make sure that the geotextile is laid flat and without folds, that it is securely fastened, and that there is no unexpected damage.

Protection of geotextiles: After laying geotextiles, it should be protected from external influences such as ultraviolet radiation, mechanical damage and chemicals. To do this, you can use additional protective layers or special coatings.

Following these steps will help ensure that geotextiles are installed correctly and remain effective throughout their lifespan.

Remember that the correct use of geotextiles is important for the durability and stability of building structures.

How to lay geotextiles correctly?

Geotextiles can be rolled out manually or using special equipment. It depends on the width of the roll. Make sure that the laying occurs in an even layer without folds or twisting. Before laying geotextiles, it is necessary to carefully remove rhizomes, stones and other debris, prepare the soil base, and level the area. When using several rolls, geotextiles are laid with an overlap, overlapping the adjacent fabric by 10-30 cm. This will help avoid mixing of layers and displacement when pouring bulk materials.

Which geotextile allows water to pass through better?

All geotextile fabrics allow water to pass through themselves well, but each type has its own water permeability indicator. The water permeability of geotextiles is determined by the amount of liquid passing through the canvas in a given period of time and is measured in l/sec/m2. The higher the density of geotextiles, the less water permeability it has. Therefore, geotextiles with a low density, from 80 to 200 g/m2, depending on the type of geotextile fabric, allow water to pass through better.

Related materials