Product code: 0138
For use in the arrangement of drainage systems and in the agricultural sector
Needle-punched geotextile has a large elongation coefficient, easily takes the necessary shape and has excellent filtering abilities in the longitudinal and transverse directions.
The main functions of geotextile:
Scope of application:
Type: Hole-piercing
Thickness at a vice of 2 kN/m2, mm: 1.5
Surface thickness, g/m2: 100
Tension spacing, kN/m: 4
Strength at 5% reduction, kN/m: 3
Stacking type:
Drainage;
Armuvannya;
Dilennya;
Zmіtsnennya;
Filtration
Punching CBR, N: 500
Building water throughput: 100 l/m2*sec
Water penetration at 20 kN/m2, 10*-4 m/s: 0.1
Dovzhina, m: 50
Width, m: 2
Dimensions (WxL), m: 2x50
Thickness, mm: 2.5
Laying geotextiles is a process that plays a key role in construction, especially when working with road surfaces, soil structures and landscaping.
Here are a few steps to help you install geotextiles correctly:
Surface preparation: Make sure the surface on which the geotextile will be laid is free of debris, sharp objects and stones. If necessary, carry out preparatory work, including leveling and compacting the soil.
Selection and installation of geotextiles : Select the appropriate type of geotextiles according to the requirements of your project. When laying geotextiles, ensure that they are distributed evenly and without folds over the entire surface. Make sure that the geotextile is not damaged during installation.
Layering : If you need to use several layers of geotextiles, lay them so that each layer overlaps the previous one by a sufficient length (usually at least 10-20 cm). This will help prevent soil penetration and maintain the integrity of the structure.
Fixation of geotextiles: It is important to ensure reliable fixation of geotextiles so that they do not move during construction work or as a result of environmental influences. To do this, you can use fasteners, pins, weights or other special devices.
Checking the installation quality: After installation is complete, check the quality of the work done. Make sure that the geotextile is laid flat and without folds, that it is securely fastened, and that there is no unexpected damage.
Protection of geotextiles : After laying geotextiles, it should be protected from external influences such as ultraviolet radiation, mechanical damage and chemicals. To do this, you can use additional protective layers or special coatings.
Following these steps will help ensure that geotextiles are installed correctly and remain effective throughout their lifespan.
Remember that the correct use of geotextiles is important for the durability and stability of building structures.
How to lay geotextiles correctly?
Geotextiles can be rolled out manually or using special equipment. It depends on the width of the roll. Make sure that the laying occurs in an even layer without folds or twisting. Before laying geotextiles, it is necessary to carefully remove rhizomes, stones and other debris, prepare the soil base, and level the area. When using several rolls, geotextiles are laid with an overlap, overlapping the adjacent fabric by 10-30 cm. This will help avoid mixing of layers and displacement when pouring bulk materials.
Which geotextile allows water to pass through better?
All geotextile fabrics allow water to pass through themselves well, but each type has its own water permeability indicator. The water permeability of geotextiles is determined by the amount of liquid passing through the canvas in a given period of time and is measured in l/sec/m2. The higher the density of geotextiles, the less water permeability it has. Therefore, geotextiles with a low density, from 80 to 200 g/m2, depending on the type of geotextile fabric, allow water to pass through better.
Geotextile can be rolled out manually or with the help of special equipment, It depends on the width of the roll. Make sure that the laying takes place in an even layer without folds and twisting. Before laying the geotextile, it is necessary to carefully remove the rhizomes, stones and other debris, prepare the soil base, level the plot. When using several rolls, the geotextile is laid overlapping with the overlap of the adjacent canvas by 10-30 cm. This will help to avoid mixing of layers and displacement when filling bulk materials.
The use of thermally fixed geotextile when laying paving slabs stabilizes the top layer of the soil, prevents the extrusion of sand and eliminates the cause of irregularities of the main pavement. For laying any paving slabs, geotextiles with a density of 120 to 200 g/m2 are used, depending on loads and traffic intensity. Geotextile is a necessary material for the arrangement of the territory. It is used in places exposed to high or frequent loads: driveways, parking lots, storage areas
Geotextile is made in the form of rolls, with a width of 2 to 6 m and a length of 50 to 150 m. The density can vary from 100 to 600 g/m2 in increments of 50 grams. The most popular density in the construction industry is 150-200 g/m2.
All geotextile fabrics pass water through themselves well, but each of the types has its own water permeability index. The water permeability of geotextiles is determined by the amount of liquid passing through the canvas in a given period of time and is measured in l/sec/m2. The higher the density of the geotextile, the less water permeability it has. Therefore, geotextile with a low density, from 80 to 200 g/m2, depending on the type of geotextile fabric, passes water better.
Retainer flooring for a protective horizontal layer of reinforcement on a loose base, soils, gravel, sand.
The floor retainer is designed to create a protective horizontal layer of 50 mm for 8-16 mm reinforcement on a solid base.
For underground structures, basement and retaining walls, tunnels, underground parking lots, road construction
Vapor barrier sealing tape-sealant SNTDrain for gluing steam, hydro barrier and membranes, 15x1.5 mm, 45 m.p
For reinforcement, improvement of mechanical properties of road concrete.
Application in road construction, for filtration and drainage systems, for hydraulic structures
© "Protex-S" LLC2021 | Website created by MD Design