Waterproofing dowel U-shaped

 

It is used for sealing and waterproofing movable joints in the monolithic construction of buried and underground structures.

Шпонка гидравлическая серии P внешняя Шпонка гидравлическая серии P внешняя

Шпонка гидравлическая серии P внешняя

Hydrospins are used in hydraulic structures (reservoirs, canals, dams, swimming pools, etc.), as well as for waterproofing joints of foundations, foundations, tunnels, multi-level parking lots and other underground structures.

They are made of thermoplastic elastomer TPE (EPDM) or plasticized polyvinyl chloride PVC-P.

Hydrospin parameters:

Name

P-1

P-2

P-3

a (mm)

50

100

140

b (mm)

25

30

40

f (mm)

30

30

30

The U - shape of the hydraulic key allows you to clearly install the key in the design position, using, for example, a sheet of expanded polystyrene, on which ?wear it? the key. The presence of ribs on the locking plane prevents the penetration of moisture into the structure.

it is used in the locations of the expansion joints of monolithic reinforced concrete structures, in particularly important structures it is supplemented with an internal or lower external hydraulic spar;

withstands low water pressure inside and outside;

suitable for all kinds of designs;

they are delivered in rolls of 25 m. p., if it is necessary to extend the rolls, they are welded together with a construction hair dryer for PVC membranes (glued together ? for TRE).

Installation Options:

Вертикальный вариант установки шпонки гидравлической Горизонтальный вариант установки шпонки гидравлической

Technical specifications:

Indicators

1

Material

Thermoplastic elastomer TPE (EPDM)

Plasticized polyvinyl chloride (PVC-P)

2

Colour

Black

Black

3

Packaging

Rolls of 25 m. p.

Rolls of 25 m. p.

4

Roll length deviation, m, not more than

0,5

0,5

5

Size deviation

According to the CD

According to the CD

6

Shore Hardness, A

60  5

70  5

7

Density, g / cm?

 0,97

1,4

8

Tensile strength, MPa

18,5(DIN 53455)

10 (DIN 53455)

9

Elongation at break, %

750

275

10

Temperature resistance, °C

from -55°C to 135

from -35°C to 70°C

11

Chemical resistance

- from constant exposure to water and wastewater, benzenes and oils;

- from short-term exposure to inorganic alkalis and acids of low and medium concentration.

- from constant exposure to water and wastewater;

- from short-term exposure to inorganic alkalis and low-concentration acids, mineral oils.

12

Shelf life

not more than 5 years, in ventilated areas, protect from direct sunlight

not more than 5 years, in ventilated areas, protect from direct sunlight

Installation procedure and rules:

The hydraulic spar is installed in the design position, so that the middle of the hydraulic spar is located in the center of the intended deformation seam. The U-shaped hydrospin is put on a sheet of expanded polystyrene or similar, elastic material of suitable thickness, and the sheet itself is fixed to the formwork and reinforcement frame. The hydrospin anchors are fixed to the reinforcement frame by means of a knitting wire with a step of 300-500 mm. 

The connection of the key made of PVC-p is made by soldering, by heating the ends of the key in a special conductor (for each key — an individual conductor) or using an industrial hair dryer. The temperature of the spike is about 200°C.

To connect the TPE dowels, a sealing adhesive is used, for example, a one-component paste-like adhesive based on the silane-modified polymer Innoellast.

Установка внешней шпонки гидравлической серии P


U-shaped hydraulic spar of the PN series

It is used for sealing and waterproofing movable joints in the monolithic construction of buried and underground structures in conjunction with existing concrete structures.

Hydrospins are used in hydraulic structures (reservoirs, canals, dams, swimming pools, etc.), as well as for waterproofing joints of foundations, foundations, tunnels, multi-level parking lots and other underground structures.

Шпонка гидравлическая серии PN внешняя Шпонка гидравлическая серии PN внешняя

Шпонка гидравлическая серии PN внешняя

They are made of thermoplastic elastomer TPE (EPDM) or plasticized polyvinyl chloride PVC-P.

Hydrospin parameters:

Name

PN-1

PH-2

PH-3

a (mm)

50

100

140

b (mm)

25

30

40

f (mm)

30

30

30

The U - shape of the hydrospin allows you to clearly set the key in the design position, using, for example, a sheet of expanded polystyrene, on which the key is put on. The presence of ribs on the locking plane prevents the penetration of moisture into the structure.

it is used in the locations of expansion joints of monolithic reinforced concrete structures when mating with an existing concrete structure, in particularly important structures it is supplemented with an internal or lower external hydraulic spar;

withstands low water pressure inside and outside;

they are delivered in rolls of 25 m. p., if it is necessary to extend the rolls, they are welded together with a construction hair dryer for PVC membranes (glued together for TPE).

Installation Options:

Вертикальный вариант установки шпонки гидравлической Горизонтальный вариант установки шпонки гидравлической

Technical specifications:

Indicators

1

Material

Thermoplastic elastomer TPE (EPDM)

Plasticized polyvinyl chloride (PVC-P)

2

Colour

Black

Black

3

Packaging

Rolls of 25 m. p.

Rolls of 25 m. p.

4

Roll length deviation, m, not more than

 0,5

 0,5

5

Size deviation

According to the CD

According to the CD

6

Shore Hardness, A

60  5

70  5

7

Density, g / cm?

0,97

1,4

8

Tensile strength, MPa

18,5(DIN 53455)

10 (DIN 53455)

9

Elongation at break, %

750

275

10

Temperature resistance, °C

from -55°C to 135

from -35°C to 70°C

11

Chemical resistance

- from constant exposure to water and wastewater, benzenes and oils;

- from short-term exposure to inorganic alkalis and acids of low and medium concentration.

- from constant exposure to water and wastewater;

- from short-term exposure to inorganic alkalis and low-concentration acids, mineral oils.

12

Shelf life

not more than 5 years, in ventilated areas, protect from direct sunlight

not more than 5 years, in ventilated areas, protect from direct sunlight

Installation procedure and rules:

The hydraulic spar is installed in the design position, so that the middle of the hydraulic spar is located in the center of the intended deformation seam. The U-shaped hydrospin is put on a sheet of expanded polystyrene or similar, elastic material of suitable thickness, and the sheet itself is fixed to the formwork and reinforcement frame. The side of the hydraulic spar that does not have anchors is glued to the existing concrete structure with InnoElast typ1 glue, if necessary, additional mechanical fastening is possible with a metal plate on the dowels. The hydrospin anchors located on the opposite side are fixed to the reinforcement frame by means of a knitting wire with a step of 300-500 mm.

The connection of the key made of PVC-p is made by soldering, by heating the ends of the key in a special conductor (for each key — an individual conductor) or using an industrial hair dryer. The temperature of the spike is about 200°C.

To connect the TPE dowels, a sealing adhesive is used, for example, a one-component paste-like adhesive based on the silane-modified polymer InnoEllast.