Internal gidroponka for work stitches series BP

 

Hydraulic spoons of the BP series are intended for waterproofing of working (technological) joints of concrete structures between the horizontal base plate and the vertical load-bearing wall, or formed during a break in concreting.

Hydrospins are used in hydraulic structures (reservoirs, canals, dams, swimming pools, etc.), as well as for waterproofing joints of foundations, foundations, tunnels, multi-level parking lots and other underground structures.

They are made of thermoplastic elastomer TPE (EPDM) or plasticized polyvinyl chloride PVC-P.

Шпонка гидравлическая серии ВР A внутренняя Шпонка гидравлическая серии ВР A внутренняя

Hydrospin parameters:

Name

BP 200

BP 240

BP 320

BP 500

a (mm)

200

240

320

500

b (mm)

80

90

110

150

c (mm)

3,5

4,0

5,0

6,0

f (mm)

15

15

20

25

The shape of the hydrospin allows you to securely embed in the concrete structure, the presence of ribs on the locking plane prevents the penetration of moisture into the structure.

it is used during the break of concreting of monolithic reinforced concrete structures, in particularly important structures it is supplemented with an external hydraulic spar;

it can be used in structures with special requirements to ensure tightness;

withstands high water pressure inside and outside;

easy to install;

suitable for all kinds of designs;

they are delivered in rolls of 25 m. p., if it is necessary to extend the rolls, they are welded together with a construction hair dryer for PVC membranes (glued together ? for TRE).

Installation Options:

Вертикальный вариант установки шпонки гидравлической Горизонтальный вариант установки шпонки гидравлической
horizon-vertical horizon-horizon

Technical specifications:

Indicators

1

Material

Thermoplastic elastomer TPE (EPDM)

Plasticized polyvinyl chloride (PVC-P)

2

Colour

Black

Black

3

Packaging

Rolls of 25 m. p.

Rolls of 25 m. p.

4

Roll length deviation, m, not more than

0,5

0,5

5

Size deviation

According to the CD

According to the CD

6

Shore Hardness, A

60 5

70  5

7

Density, g / cm

0,97

1,4

8

Tensile strength, MPa

18,5 (DIN 53455)

10 (DIN 53455)

9

Elongation at break, %

 750

 275

10

Temperature resistance, °C

from -55°C to 135

from -35°C to 70°C

11

Chemical resistance

- from constant exposure to water and wastewater, benzenes and oils;

- from short-term exposure to inorganic alkalis and acids of low and medium concentration.

- from constant exposure to water and wastewater;

- from short-term exposure to inorganic alkalis and low-concentration acids, mineral oils.

12

Shelf life

not more than 5 years, in ventilated areas, protect from direct sunlight

not more than 5 years, in ventilated areas, protect from direct sunlight

Installation procedure and rules:

The hydraulic spar is installed in the design position, so that the middle of the hydraulic spar is located in the center of the intended seam.

Fastening is made with the help of special clips or through holes on the edges of the key with knitting wire. Mounting pitch-200-300 mm, symmetrical on both sides. Fixing is made to the reinforcement frame and the formwork sheets.

The connection of the key made of PVC-p is made by soldering, by heating the ends of the key in a special conductor (for each key - an individual conductor) or by using an industrial hair dryer. The temperature of the spike is about 200°C.

To connect the TPE dowels, a sealing adhesive is used, for example, a one-component paste-like adhesive based on the silane-modified polymer Innoellast.

Установка шпонки внутренней серии ВР A внутренняя